[Q11-Q32] Full D-SNC-DY-00 Practice Test and 47 Unique Questions, Get it Now!

4.8/5 - (5 votes)

Full D-SNC-DY-00 Practice Test and 47 Unique Questions, Get it Now!

The Best D-SNC-DY-00 Exam Study Material Premium Files and Preparation Tool

NO.11 What are two characteristics of route maps in Enterprise SONIC?

Route-map names are not case-sensitive.

The permit or deny clause In route maps permits or rejects the matching routes from being redistributed.

They are a series of commands that contain a matching criterion and action.

Each route map clause has the type values of Match. Set. and Act.

NO.12 Refer to the exhibit.

What is the primary VRRP router for VRRP group 10?

Router-1

Router-2

Router-3

NO.13 VLAN 40 is configured in Switch A with an anycast-address of 192.168.40.254/24. The ARP neighbor suppression is enabled. Use the simulator to create a VTEP named vtep1 and assign an IP address of
10.10.10.1. Map the VNI 400 to VLAN 40.

NO.14 An administrator obtains the following CLI output:

How much time does the local system take to detect remote failures without receiving packets?

600 milliseconds

900milliseconds

1200 milliseconds

800 milliseconds

NO.15 What does the show vian command display?

All configured VLANs

Only VLANs in an active state

All 4094 VLANs

NO.16 Refer to the exhibit.

What can be determined from this show command?

Traffic below 100 KB is marked as congested

ECN is enabled for all colors

ECN is enabled for all DSCP values

There is a 10% probability that traffic is marked as congested

NO.17 What is an iBGP neighbor relationship?

Two BGP neighbors have the same autonomous system numbers

Two BGP neighbors share L2VPN EVPN advertisements.

Two BGP neighbors share only native BGP networks.

Two BGP neighbors share only private networks.

NO.18 What is a correct use-case scenario for ZTP in Enterprise SONiC?

The user wants single pane of glass monitoring.

The user wants multivendor switch deployment.

The user wants to configure the switch manually using the CLI.

The user wants to replace a failed unit and use an automatic script.

NO.19 Configure a VRF called “VrfGreen” and the static route in it to network 172.16.128.64/28 through next-hop
10.10.10.1. Set an administrative distance of 213.

NO.20 In what order should these commands be entered to configure an access port in SONiC CLI if the required VLAN is already configured?

NO.21 An administrator is installing Enterprise SONIC in ONIE from an HTTP server.
On which interface should the administrator configure the IP?

Mgmt1/1/1

GiO

ethO

Eth1/1

NO.22 How many port channels can be assigned to a single port?

NO.23 What is a correct use-case scenario for ZTP in Enterprise SONiC?

The user wants single pane of glass monitoring.

The user wants to replace a failed unit and use an automatic script.

The user wants multivendor switch deployment.

The user wants to configure the switch manually using the CLI.

NO.24 Refer to the exhibit.

The route distinguisher was autogenerated. Which VLAN is mapped to VNI410?

VLAN 410

VLAN41

VLAN 10

VLAN 26

NO.25 Use the simulator to perform the following configuration task.
1. Map a single-tagged CVLAN 100 to SVLAN 200 translation on PE
switch interface Eth1/1.
2. Map a double-tagged VLAN packet with an outer CVLAN 100 and an
inner dot1q 200 to SVLAN 300 translation on PE switch interface
Eth1/2.
The necessary VLANs and VLAN stacking have already been configured.

NO.26 How many times must BGP be configured when running symmetric IRB with two VFRs?

NO.27 What are the supported modes for the QSFP28 ports on an S5248F?

1x100G, 1×40 G, 2×50 G, and 4×25 G

1x100G, 1×40 G, 4×25 G, and 4×10 G

1x200G, 1×100 G, 1×40 G, and 4×25 G

1x400G, 2×200 G, 4×25 G. and 4×10 G

NO.28 What are three characteristics of VLAN translation?

VLAN translation is not supported on MC-LAG port channel interfaces.

Trunk or access ports can be configured as members of any VLANs that are not used as an SVLAN.

By default, VLAN stacking is enabled on Z9432F-ON switches.

The SVLAN header is replaced with a VNI if the provider network uses a VXLAN overlay.

SVLAN configuration for both Q-in-Q VLAN tunneling and VLAN translation is possible on the same interface.

NO.29 Refer to the exhibits.

PC1 has a valid address on the 192.168.10.0 network, and PC2 has a valid address on the 192.168.20.0 network.
What happens when a ping command is issued between PC1 and PC2?